Accueil Services Calibration services

Calibration services

At HEMERA RF, we handle all of your EMC and microwave calibrations: selection of accredited service providers, round-trip transport, coordination and monitoring.

By entrusting this responsibility to us, you free up your teams. And thanks to meticulous joint planning, your laboratory's activities are maintained.

EMC calibration: which equipment is covered?

We manage the calibration of a wide range of equipment dedicated to EMC and microwave applications:

Whatever the equipment, we validate with you the calibration programme suited to your needs and maintenance cycles.

ISO 17025 and COFRAC accredited calibration

Calibration consists of comparing your device with a certified reference standard to measure its deviation from its nominal value. This process ensures the reliability and traceability of your measurements over time.

We work with accredited French and European service providers, guaranteeing calibrations that meet the strictest requirements:

  • COFRAC accredited calibration or European equivalent: compliant with international recommendations and enforceable in the event of an audit
  • Custom programmes: tailored to your specifications and operational constraints
  • Adjustment and verification: checking manufacturer specifications to make sure your devices remain within tolerance
  • Performance measurements: Faraday cages and anechoic chambers, for both new and existing installations

Our accredited partners include Seibersdorf Laboratories, Eurofins York and Kiwa, three European benchmarks in RF and EMC metrology.

A single point of contact for all your EMC calibrations

Between two calibration cycles, your equipment may drift without you knowing it. Intermediate checks, or equipment verifications, detect these deviations before they affect the reliability of your measurements and the validity of your EMC test results.

We build these checks into your calibration programme to give you continuous traceability and complete peace of mind.

Intermediate checks: an essential step between two calibrations

Our hands-on expertise in EMC and microwave equipment allows us to define exactly which programmes to apply, with which providers and in which order, so that your laboratory's activities are never interrupted.

In practice, you benefit from:

  • A single point of contact for all your calibrations
  • Joint planning that preserves your laboratory's continuity
  • Full management of round-trip transport
  • Rigorous tracking of certificates and due dates

We also offer repair and EMC project support services to provide comprehensive follow-up of your equipment.

Frequently asked questions

Frequently asked questions
Calibration / metrology

Why does EMC equipment need to be calibrated?

Calibration makes it possible to:
• know how the equipment deviates from reference values
• assign uncertainties to the results
• monitor drift
• ensure appropriate metrological traceability
• control the quality of EMC and RF measurements

What is the difference between calibration and verification?

• Calibration: establishes the relationship between the instrument’s readings and reference values, with the associated uncertainties.
• Verification: uses measurement results to determine whether the equipment meets specified requirements.

What is the ISO/IEC 17025 standard?

ISO/IEC 17025 sets out the general requirements for the competence of testing and calibration laboratories.
It covers in particular:
• competence
• impartiality
• consistent operation of laboratories
• control of methods and equipment
• validity and traceability of results
It is the leading international standard for the accreditation of testing and calibration laboratories.

What is the difference between ISO/IEC 17025 and COFRAC?

A distinction must be made between:
• ISO/IEC 17025: the standard that defines the requirements
• COFRAC: the French accreditation body
• accreditation: formal recognition of competence for specified activities
• scope of accreditation: the specific services for which the laboratory is accredited
It is therefore not enough for a laboratory to be accredited: you must check that the calibration you need falls within its scope of accreditation.

What is the difference between accredited and non-accredited calibration?

Accredited calibration:
• performed within a scope of accreditation
• laboratory assessed against the applicable requirements
• formal recognition of competence for the service concerned
Non-accredited calibration:
• may meet certain technical or internal needs
• does not carry, for that service, the same recognition through accreditation
The choice depends on regulatory, contractual and quality requirements.

What is a COFRAC calibration?

The term commonly refers to a service that is:
• performed under COFRAC accreditation
• covered by the laboratory’s scope of accreditation
• subject to the applicable requirements of EN ISO/IEC 17025
You should therefore always check the scope for the quantity and service required.

Is a calibration performed by a European laboratory recognised in France?

You should check in particular:
• the body that granted the accreditation
• the scope of accreditation
• the service concerned
• the applicable mutual recognition agreements
• any contractual requirements of the customer

Which EMC equipment needs to be calibrated?

• EMI receivers
• analysers
• RF generators
• power meters
• power sensors
• field probes
• antennas
• LISNs
• current clamps and probes
• other instruments or devices with a significant metrological function

How should the calibration interval for a piece of equipment be set?

The factors to consider include:
• manufacturer’s recommendations
• frequency of use
• operating conditions
• criticality of the measurement
• metrological risk
• history of results
• observed stability of the equipment
The interval therefore need not be the same for all equipment.

What should a calibration certificate contain?

It should make it possible to identify:
• the equipment
• the results
• the method used
• the relevant conditions
• the uncertainties, where required
• the references needed for traceability
• the accreditation status of the service, when it is performed under accreditation

How can metrological traceability of EMC equipment be ensured?

In particular, you need to:
• identify the equipment
• manage certificates
• track due dates
• analyse successive results
• keep a history
• carry out intermediate checks where necessary
• maintain a documented metrological traceability chain

Would you like us to manage your EMC calibrations?

Contact us
logo seibersdorf laboratories
logo eurofins york